Grizzly G0516 Uživatelský manuál Strana 19
- Strana / 72
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
G0516 Lathe/Mill -17-
Test Run Mill/Drill
Before continuing to the Operations section, test
run the mill/drill to verify that it runs properly.
To test run the mill/drill:
1. Make sure that the factory installed drill
chuck is tight, that there is not a chuck key in
the chuck, and that the eyeshield is firmly
mounted between you and the drill chuck.
Make this step a habit that you perform every
time you start the lathe.
2. Plug the machine into the power outlet.
3. Familiarize yourself with the mill/drill controls
shown in Figures 11 and 12.
Figure 11. Mill/drill controls.
Figure 12. Mill/drill controls.
4. Rotate the Lathe/Mill selector switch to the
“MILLING” position.
5. Move the high/low speed lever to the “L”
position for low speed.
6. Unlatch mill/drill emergency stop switch
cover—this should make the mill/drill power
indicator light up.
7. Rotate the variable speed knob clockwise to
turn the mill/drill spindle ON. The farther you
rotate the variable speed knob, the faster the
mill/drill spindle will rotate.
8. Rotate the variable speed dial clockwise as
far as it will go, so the drill chuck is spinning
at top speed.
9. Rotate the variable speed dial counterclock-
wise as far as it will go. This should stop the
drill chuck.
10. Press the mill/drill emergency stop button to
turn the mill/drill OFF.
11. Move the high/low speed lever to the “H”
position for high speed.
12. Unlatch mill/drill emergency stop switch
cover—this should make the mill/drill power
indicator light up.
13. Rotate the variable speed knob clockwise to
turn the mill/drill spindle ON. The farther you
rotate the variable speed knob, the faster the
mill/drill spindle will rotate.
14. Rotate the variable speed dial clockwise as
far as it will go, so the drill chuck is spinning
at top speed.
15. Rotate the variable speed dial counterclock-
wise as far as it will go. This should stop the
drill chuck.
16. Press the mill/drill emergency stop button to
turn the mill/drill OFF.
Emergency
Stop Switch
High/Low
Speed Lever
Variable
Speed Knob
- COMBINATION LATHE/MILL 1
- INSTRUCTION MANUAL 1
- TABLE OF CONTENTS 3
- SECTION 1: SAFETY 4
- 110V Operation 7
- Extension Cords 7
- Grounding 8
- SECTION 3: INTRODUCTION 9
- SECTION 4: IDENTIFICATION 10
- SECTION 5: SET-UP 12
- Site Considerations 14
- Clean Up 14
- Attach Mill/Drill to 16
- Eyeshield 17
- Test Run Lathe 18
- Test Run Mill/Drill 19
- SECTION 6: LATHE OPERATIONS 20
- Removing Chuck 21
- Installing Chuck 22
- Installing Tailstock 22
- Dead Center 22
- Removing Tailstock 23
- Adjusting Tailstock 23
- Longitude Position 23
- Changing 24
- Tool Posts 24
- Adjusting 25
- Compound Slide 25
- Cross Slide 25
- Adjusting Carriage 26
- Understanding 27
- Gear Charts 27
- 16 18 20 24 28
- 0.4 0.5 0.6 0.7 28
- 16 18 20 24 32 40 28
- Changing Gears For 30
- Carriage Feed Rate 30
- Reverse Threading 32
- Changing Speeds 34
- Mill/Drill 35
- Changing Chucks 36
- Installing Mill Table 38
- SECTION 8: MAINTENANCE 39
- Checking V-Belt 40
- Maintenance Log 41
- About Service 42
- Aligning Tailstock 44
- Bearing Preload 45
- Service Log 46
- SECTION 10: REFERENCE INFO 47
- MACHINE DATA 48
- G0516 Lathe/Mill -47 49
- G0516 Lathe/Mill 50
- REF PART # DESCRIPTION 51
- TIMING BELT 1.5 X 124 X 15MM 63
- G0516 Lathe/Mill -63 65
- Warranty and Returns 68
- WARRANTY CARD 69
- FOLD ALONG DOTTED LINE 70
- &2%% 72
Související produkty a manuály pro Nástroje Grizzly G0516
Nástroje Grizzly G9908 Uživatelský manuál
(10 stránky)
(10 stránky)
Nástroje Grizzly G9247 Uživatelský manuál
(14 stránky)
(14 stránky)
Nástroje Grizzly T23092 Uživatelský manuál
(16 stránky)
(16 stránky)
Nástroje Grizzly H8225 Uživatelský manuál
(22 stránky)
(22 stránky)
Nástroje Grizzly Model H8222 Uživatelský manuál
(16 stránky)
(16 stránky)
Nástroje Grizzly G4002 Uživatelský manuál
(54 stránky)
(54 stránky)
Nástroje Grizzly H7761 Uživatelský manuál
(2 stránky)
(2 stránky)
Nástroje Grizzly H3256 Uživatelský manuál
(24 stránky)
(24 stránky)
Nástroje Grizzly G0624 Uživatelský manuál
(36 stránky)
(36 stránky)
Nástroje Grizzly T23093 Uživatelský manuál
(2 stránky)
(2 stránky)
Nástroje Grizzly G0632 Uživatelský manuál
(56 stránky)
(56 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 1.284 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce